Is your car affected?
Check by VIN to confirm the
exact model and see every recall for it.
Recalls are issued for a make, model and model year. Whether the repair has already been done on one specific car is known only to its manufacturer and dealers. Check your vehicle's official status at nhtsa.gov/recalls or with a dealer.
US recalls (2)
Steering: linkages
ON CERTAIN PASSENGER VEHICLES INVOLVED IN THIS CAMPAIGN, THE LOWER CONTROL ARM BALL STUD NUT/WASHER ASSEMBLIES WITH WASHERS WERE MADE OF THE WRONG MATERIAL. THE WASHERS MAY FRACTURE AND BECOME LOOSE OR FALL AWAY FROM THE VEHICLE, REDUCING CLAMP LOAD. SEPARATION OF THE CONTROL ARM BALL STUD AND STEERING KNUCKLE, DUE TO DISENGAGEMENT OF THE TAPERED ATTACHMENT AND RETAINING NUT, IS POSSIBLE.
Risk and remedy
Risk: IF THE CONTROL ARM SEPARATES FROM THE KNUCKLE, THE AFFECTED CORNER OF THE VEHICLE WILL DROP AND THE CONTROL ARM WOULD BE FORCED DOWNWARD, CONTACTING THE WHEEL. THE AFFECTED WHEEL COULD TILT OUTWARD AND CREATE A DRAGGING ACTION THAT WOULD TEND TO SLOW THE VEHICLE AND CREATE A TENDENCY FOR THE VEHICLE TO TURN IN THE DIRECTION OF THE AFFECTED WHEEL. IN EXTREME SITUATIONS, THE AFFECTED WHEEL ASSEMBLY COULD SEPARATE FROM THE VEHICLE. SEPARATION OF THE WHEEL ASSEMBLY WOULD ALSO SEVER THAT WHEEL;S HYDRAULIC BRAKE HOSE AND RESULT IN DIMINISHED BRAKING PERFORMANCE OF THE VEHICLE, WHICH COULD RESULT IN A CRASH.
Remedy: DEALERS WILL INSPECT THE BALL STUD JOINTS AND MEASURE THE TORQUE OF THE NUT FOR ALL FRONT LOWER CONTROL ARMS IN ALL MODELS AFFECTED AS WELL AS THE REAR LOWER CONTROL ARMS ON THE XLR AND CORVETTE. IF THE TORQUE IS NOT AT SPECIFICATION, THE DEALERS WILL REPLACE THE BALL STUD, THE KNUCKLE, AND THE NUT. IF THE TORQUE IS AT SPECIFICATION, THE DEALERS WILL REPLACE THE NUT/WASHER ASSEMBLY ONLY. THE RECALL WILL BEGIN ON AUGUST 25, 2004. OWNERS SHOULD CONTACT CADILLAC AT 1-866-982-2339 OR CHEVROLET AT 1-800-630-2438.
Steering: column locking, anti-theft device
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH ELECTRONIC COLUMN LOCK SYSTEMS (ECL), WHEN THE IGNITION SWITCH IS TURNED TO "LOCK," THE ECL SYSTEM PREVENTS TURNING OF THE STEERING SYSTEM. WHEN THE VEHICLE IS STARTED, THE ECL UNLOCKS THE STEERING SYSTEM. THE VEHICLE IS DESIGNED SO THAT IF THE COLUMN FAILS TO UNLOCK WHEN THE VEHICLE IS STARTED AND THE CUSTOMER TRIES TO DRIVE, THE FUEL SUPPLY WILL BE SHUT OFF SO THAT THE VEHICLE CANNOT MOVE WHEN THE VEHICLE CANNOT BE STEERED. IF VOLTAGE AT THE POWERTRAIN CONTROL MODULE IS LOW OR INTERRUPTED, HOWEVER, THE FUEL SHUT OFF MAY NOT OCCUR AND THE VEHICLE CAN BE ACCELERATED WHILE THE STEERING SYSTEM IS LOCKED. ALSO WHEN THE CONTROL SYSTEM SHOWS THAT THE ECL IS UNLOCKED AND THE VEHICLE IS BEING DRIVEN, THE LOCK PIN LOCATION CAN VARY. DEPENDING ON THE LOCATION OF THE LOCK PLATE RELATIVE TO THE SWITCH TRANSITION POINT, THERE COULD THEN BE CONTACT BETWEEN THE LOCK PLATE AND PIN CAUSING THE STEERING TO LOCK WHILE DRIVING .
Risk and remedy
Risk: IF THIS OCCURS, A CRASH COULD OCCUR WITHOUT WARNING.
Remedy: ON VEHICLES EQUIPPED WITH AN AUTOMATIC TRANSMISSION, THE DEALER WILL DISABLE THE STEERING COLUMN LOCK BY REMOVING THE COLUMN LOCK PLATE. WHEN THE IGNITION KEY IS REMOVED, THE TRANSMISSION SHIFTER WILL LOCK BUT THE STEERING COLUMN WILL NOT LOCK. ON VEHICLES EQUIPPED WITH A MANUAL TRANSMISSION, THE DEALER WILL REPROGRAM THE POWERTRAIN CONTROL MODULE, PERFORM A DIMENSIONAL CHECK OF THE COLUMN LOCK AND, IF NECESSARY, REPLACE THE LOCK PLATE. THE STEERING COLUMN ON THESE VEHICLES WILL CONTINUE TO LOCK WHEN THE KEY IS REMOVED. OWNER NOTIFICATION TO OWNERS OF 1997 VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS BEGAN ON APRIL 26, 2004. OWNERS OF 1998 THROUGH 2004 VEHICLES (EXCEPT 1997-1998 MANUAL TRANSMISSION VEHICLES) WILL BE NOTIFIED BEGINNING ON AUGUST 2, 2004. THE REMAINING OWNERS (1997-1998 MANUAL TRANSMISSION VEHICLES) WILL BE NOTIFIED LATER IN 2004, WHEN PARTS ARE AVAILABLE. OWNERS SHOULD CONTACT CHEVROLET AT 1-800-630-2438.
Canadian recalls (2)
Show 2 Canadian recalls
Suspension
2004-06-07 · campaign 2004-206
Certain vehicles were produced with lower control arm ball stud nut/washer assemblies with washers made of the wrong steel material. The washers may fracture and become loose or fall away from the vehicle, reducing clamp load. Separation of the control arm ball stud and steering knuckle, due to disengagement of the tapered attachment and retaining nut, is possible and may occur without prior indication to the vehicle operator. If the control arm separates from the knuckle, the affected corner of the vehicle will drop and the control arm would be forced downward, contacting the wheel. The affected wheel could tilt outward and create a dragging action that would tend to slow the vehicle and create a tendency for the vehicle to turn in the direction of the affected wheel. In extreme situations, the affected wheel assembly could separate from the vehicle. Separation of the wheel assembly would also sever that wheel's hydraulic brake hose and result in diminished braking performance of the vehicle, which could result in a crash. Correction: Dealers will install a new nut and washer, and if required, replace the ball stud and/or steering knuckle.
Steering
2004-02-09 · campaign 2004-052
On certain vehicles equipped with Electronic Column Lock systems (ECL), when the ignition switch is turned to "Lock", the ECL prevents turning of the steering system. When the vehicle is started, the ECL unlocks the steering system. The vehicle is designed so that if the column fails to unlock when the vehicle is started and the customer tries to drive, the fuel supply will be shut off so that the vehicle cannot move when the vehicle cannot be steered. If voltage at the Powertrain Control Module (PCM) is low or interrupted, the fuel shut off may not occur and the vehicle can be accelerated while the steering system is locked. Correction: On vehicle equipped with an automatic transmission, the dealer will disable the steering column lock by removing the column lock plate. When the ignition key is removed, the transmission shifter will lock but the steering column will not lock. On vehicle equipped with a manual transmission, the dealer will reprogram the PCM. The steering column on these vehicles will continue to lock when the key is removed..
Owner complaints (217)
Owners filed 217 complaints with NHTSA about the 2004 Chevrolet Corvette (4 crashes, 1 fires, 2 injuries reported). Among 52 model years of this model, it ranks #9 for the most complaints (median 34).
| Most-reported problem | Complaints | |
|---|
| Fuel system, gasoline | 95 | |
| Fuel/propulsion system | 52 | |
| Steering | 36 | |
| Electrical system | 11 | |
| Electronic stability control (esc) | 8 | |
| Service brakes | 7 | |
| Traction control system | 5 | |
| Visibility | 4 | |
Crash test ratings
NHTSA 5-Star Safety Ratings for the 2004 Chevrolet Corvette.
| Version | Overall | Frontal | Side | Rollover |
|---|
| 2004 Chevrolet Corvette 2-DR. | – | – | – | – |
Fuel economy
EPA ratings for each 2004 Chevrolet Corvette version.
| Version | City MPG | Highway MPG | Combined | Yearly fuel cost |
|---|
| Corvette 5.7 L Automatic 4-spd | 16 | 23 | 19 | $4,350 |
| Corvette 5.7 L Manual 6-spd | 17 | 26 | 20 | $4,100 |
Need this data in your app?
Recalls, complaints, crash ratings and fuel economy as a JSON API. Decode up to 50 VINs per call and get a daily feed of new recalls.
Explore the API →Sources: NHTSA recalls, complaints and 5-Star Safety Ratings, US EPA fuel economy and Transport
Canada's Vehicle Recalls Database (contains information licensed under the Open Government Licence – Canada).
Recalls updated 2026-10-30.